running rigging

Mirror standing rigging set £ 31.99 + £3.50 PP

1 x forestay 2 x shrouds. 1x jib strop

Made from 316 marine grade 2.5mm stainless steel

with clear plastic covering on top end to reduce wear on the top of mast

Mirror halyard set £10.50 + £1.70 PP

This set consists of a main and a jib halyard for a Mirror dinghy, they are

each 24ft long and are 4mm 8 plait pre stretched polyester

Mirror main sheet 6 mtrs £5.94 + £1.70 PP

8mm braid (while stock lasts)

Mirror kicking strap £25.50 +£2.50 PP

This is a 3 to 1 kicker for a Mirror dinghy.

It consists of a holt becket block and V cleating twin block with a 3 to 1 purchase

The line used is 4mm 8 plait which is sown on to the becket block. The loop over the

boom is made from 3mm wire with a plastic covering to protect the boom from chafe.

We can supply this kicker in either solid blue or solid red.

IF YOU HAVE A PREFERENCE PLEASE E-MAIL US ON PURCHASE

Side entry clamcleat £5.99 +£1.75 PP

CL217 mk1 or mk2 port or stbd ideal for Mirror dinghy spinnaker sheets

Mirror dinghy spinnaker crane £11.99 +£2.25 PP

The spinnaker crane fits neatly on top of the mast,

made of stainless steel and hard wearing sheeve block,

ideal for that upgrade to the racing fleet

Mirror spinnaker pole mast bracket £8.40 + £1.75pp

The bracket is made of stainless steel and designed for the Mirror mast

ideal for that upgrade to the racing fleet.

A set of 5 Mirror rubber bungs £2.50 +£1.70pp

These are standard size that fit the HA123 side and back air tank holes,

as well as the forward storage compartments.

Mirror dinghy goose neck (std ) £10.50 +£2.25 pp

Mast approx- 50 - 70mm

Boom size- 43mm

Mirror Gaff Band £3.50 +£1.70 pp

Suits section 44mm x 44mm

Holt screw in bungs x2 £4.99 +£1.70 pp

For Mirror, GP14, Wayfarer or any dinghy with solid air tanks.

Dinghies with molded or wooden tanks need to have a chance to dry out

between trips because although you sponge and dry the cockpit out and

then cover her up Sunday evening the tanks are still wet, which can be the

start of electrolisis in grp or rot on ply wood and being on the inside cannot

be seen until its to late. These bungs have fixing holes 36mm apart,

the drain plug fitting has an outside dia. of 22mm

Mirror batten set £9.99 + £2.25 pp

A set of three 10mm untapered battens complete

with o/b end fittings,

Racing burgee £6.99 + £1.70 pp

Racing pro flag by Holts, s/s rod is 410mm, Flag is 140mm x 110mm

colours available are,- Red, pink, yellow, blue.

Colours can be requested but not always guaranteed

Burgee mast clip £

Racing flag stainless steel mast clip by Holt

Vernier rigging adjuster £7.99 + £1.75 pp

They have a range of 64mm in increments of 3mm with an internal width of 9mm

and an all up weight of just 41g.

Transom gudgeon £4.99 + £1.75 pp

S/S with overall width of 70mm,

hole or pin dia. 8mm,

transom to pin centre 18mm

Transom pintle £6.50 +£2.00 pp

S/S

Rudder retaining clip £1.99 +1.70 pp

Made from marine grade s/steel to fit the above

Rudder gudgeon £14.50 + £2.00 pp

S/S fits std mirror rudder stock

Rudder pintle £14.50 + £2.00 pp

s/s fits std mirror rudder stock

Wayfarer standing rigging set £34.99 +£3.50pp

1 x forestay 2 x shrouds. Made from 316 marine grade 3mm stainless

Wayfarer 10 to 1 complete kicker system £45.99 +£2.70 pp

This kicker system consist of a - 610mm strop 3mm by 1x19 marine grade stainless steel,

20mm dynamic double bearing block and becket,

20mm dynamic triple bearing block

1x single block,

2mtr of red 4mm 8plait,

2mtr of blue 4mm 8plait,

The system now used by Mike Mcnamara

This will also fit a GP14 and Enterprise

Wayfarer main halyard £24.99 + £3.00 pp

Wayfarer main halyard made from 3mm 7X19 S/S wire rope, complete with

4mm rope tail spliced on. Unlike the genoa halyard there is not a standard

length, we will need a measurement or pattern.

PLEASE ADVISE US ON PURCHASE.

Wayfarer genoa halyard £23.99 +£3.00 pp

Wayfarer genoa halyard made from 3mm 7X19 S/S wire rope, complete with

4mm rope tail spliced on.

IT IS MADE TO STANDARD LENGTH OF 20' 11" (6.38MTRS)

IF YOU REQUIRE SPECIAL LENGTHS PLEASE ADVISE US ON PURCHASE.

Wayfarer main sheet £9.90 +£3.00 pp

10 mtrs long made from 8mm braid

Racing burgee £6.99 + £1.70 pp

Racing pro flag by Holts, s/s rod is 410mm, Flag is 140mm x 110mm

colours available are,- Red, pink, yellow, blue.

Colours can be requested but not always guaranteed

Burgee mast clip

Racing flag stainless steel mast clip by Holt

Highfield lever £29.99 +£2.70 pp

Ratchet type tension lever with 16mm wide back plate weight 193gms

Vernier rigging adjuster £7.99 + £1.70 pp

They have a range of 64mm in increments of 3mm with an internal width of 9mm

and an all up weight of just 41g.

Halyard tooth rack £5.99 +£1.70 pp

Used on Wayfarers, GP14, Enterprise, etc.

This is a ten tooth halyard adjustment suitable for wire halyards

Length 126mm, max. wire dia. 5mm, weight 31g

New set of Wayfarer battens £22.50 +£3.00 pp

A set of four 10mm aquabatten tapered battens complete

with both end fittings, the lengths are -

3 x 800mm inc end fittings

1 x 600 inc end fittings

Set of 15mm untapered battens £12.99 +£2.70 pp

same as above but untapered.

Enterprise standing rigging £34.99 +£3.50 pp

This rigging is made from 3mm 1x19 s/s wire complete with copper ferrels

and s/s thimbles both ends.We will need your measurments as there have been

many different masts over the years.

Enterprise genoa halyard £23.99 + £3.00 pp

Enterprise genoa halyard made from 3MM 7X19 S/S wire rope, complete with

4mm rope tail spliced on.

The wire has an eye with s/s thimble one end and a soft eye in the other where the

rope is spliced.

A PATTEN IS REQUIRED OR YOU CAN MEASURE AND SEND US YOUR LENGTHS

Enterprise main halyard £25.99 + £3.00 pp

Enterprise main halyard made from 3mm 7X19 S/S wire rope, complete with

4mm rope tail spliced on.

A PATTEN IS REQUIRED OR YOU CAN MEASURE AND SEND US YOUR LENGTHS

Main sheet £9.90 +£3.00 pp

10 mtrs long made from 8mm braid

New set of Enterprise tapered battens £18.50 +£2.70 pp

A set of three 10mm aquabatten tapered battens complete

with both end fittings, the lengths are -

2x 800mm inc end fittings

1x 600mm inc end fittings

Set of Enterprise untapered battens £10.99 + £2.70 pp

A set of three 10mm tapered battens complete

with both end fittings, the lengths are -

2x 800mm inc end fittings

1x 600mm inc end fittings

ClicGP14 standing rigging set (Lengths required ) £34.99 + £3.50 pp

Complete with two shrouds and one forestay, all in 3mm 1x19 s/s

Please note Our standard set comes with hard eyes with copper ferrels at both ends.

We can also supply the set of Standing Rigging with T Terminals Email for prices

GP14 main halyard £25.99 + £3.00 pp

PLEASE NOTE

A PATTEN IS REQUIRED OR YOU CAN MEASURE AND SEND US YOUR LENGTHS

GP14 jib halyard £23.99 + £3.00 pp

PLEASE NOTE

A PATTEN IS REQUIRED OR YOU CAN MEASURE AND SEND US YOUR LENGTHS

Main sheet £9.90 + £3.00 pp

10 mtrs long made from 8mm braid

Set of GP14 tapered battens £18.50 + £2.70 pp

A set of three 10mm aquabatten tapered

with both end fittings, the lengths are -

2 x 800mm inc end fittings

1 x 600mm inc end fittings

Set of GP14 untapered battens £10.99 + £2.70 pp

A set of three 15mm untapered battens complete

with both end fittings, the lengths are -

2 x 800mm inc end fittings

1 x 600mm inc end fittings k here to add text.

We can supply all of the other Laser 2 standing rigging,

ie upper & lower shrouds, mail us for a quote.

Laser 2 jib Halyard £23.99 +£3.00 pp

Laser 2 genoa halyard made from 3mm 7X19 S/S wire rope, complete with

4mm rope tail spliced on.

Laser 2 Main Halyard £25.99 +£3.00 pp

Laser 2 main halyard made from 3mm 7X19 S/S wire rope, complete with

4mm rope tail spliced on.

A set of (2) Laser 2 Trapeze Wires £69.99 + £3.50 pp

A set of 2 x Laser 2 trapeze wires made from 2.5 s/s wire with s/s eyes and

copper ferrules. They come complete with handles and clam cleat trapeze cleats

and s/s loops with purchase adjustment and shock cord. Ready to fit.

Laser 2 Forestay £10.99 + £1.70 pp

Made from 1.5mm s/s wire with copper ferrels and s/s thimbles each end.

Always Worth having a spare in your tool box.

Main sheet £9.90 + £3.00 pp

10 mtrs long made from 8mm braid

Heron Rigging set £31.99 + £3.00 pp

This is a set of 2.5mm 1 x 19 standing rigging including two shrouds one forestay.

All have copper ferrules stainless steel thimbles. The top loops are covered with

hard wearing clear plastic tubing to reduce wear on the top of the mast.

Our shrouds are 3.380mm and our forstay is 3.215mm

Check to make sure you have the same measurments as us as some boats vary,

if not we will make them to your sizes.

Halyard set £10.99 + £1.70 pp

This set consists of a main and a jib halyard for a Heron dinghy, they are

each 24ft long and are 4mm 8 plait pre stretched polyester

Main sheet £9.90 +£3.00 pp

10 mtrs long made from 8mm braid

Click

Complete set of Albacore rigging. £34.99 + £3.00 pp

A pattern or your sizes are required

This is a set of new 3mm and 2.5mm 1x19 marine grade stainless Albacore

standing rigging complete with two shrouds in 3mm and one forestay in 2.5mm 1x19,

all with top quality copper ferrules and stainless thimbles both ends, ideal to have

as a spare or just treat your boat for this season. This set is with copper ferrels and

eyes each end

We can also supply sets with T terminal swages

ALBACORE MAIN HALYARD £25.99 + £3.00 pp

THIS IS A ALBACORE MAIN HALYARD MADE FROM

3MM 7X19 S/S WIRE ROPE, COMPLETE WITH 4MM ROPE TAIL SPLICED ON.

THERE IS NOT A STANDARD LENGTH

We will need a measurement or pattern. Please advise us on purchase.

ALBACORE JIB HALYARD £23.99 + £3.00 pp

THIS IS AN ALBACORE GENOA HALYARD MADE FROM

3MM 7X19 S/S WIRE ROPE, COMPLETE WITH 4MM ROPE TAIL SPLICED ON.

THERE ARE NOT ANY STANDARD LENGTHS

We will need a measurement or pattern. Please advise us on purchase.

Set of Albacore Tapered battens £22.50 + £3.00 pp

A set of four 10mm aquabatten tapered battens complete with both end fittings,

the lengths are -

2x 30in inc end fittings,

1x 27in inc end fittings,

1x 21in inc end fitting,

If you need them shorter let me have the overall size and we will cut them to size.

Set of untaperedAlbacore battens £12.99 + £2.70 pp

the lengths are -

2x 30in inc end fittings,

1x 27in inc end fittings,

1x 21in inc end fitting,

Main sheet £9.90 + £3.00 pp

10 mtrs long made from 8mm braid